Detailed Description

This "software driver" implements the communication protocol for interfacing a SICK LMS100 laser scanners through an ethernet controller.

This class does not need to be bind, i.e. you do not need to call C2DRangeFinderAbstract::bindIO. Connection is established when user call the turnOn() method. You can pass to the class's constructor the LMS100 's ip address and port. Device will be configured with the following parameters :

Start Angle : -45 deg (imposed by hardware)
Stop Angle : +225 deg (imposed by hardware)
Apperture : 270 deg (imposed by hardware)
Angular resolution : 0.25 deg
Scan frequency : 25 Hz
Max Range : 20m (imposed by hardware).

Important note: SICK LMS 1xx devices have two levels of configuration. In its present implementation, this class only handles one of them, so before using this class, you must "pre-configure" your scanner with the SICK's software "SOAP" (this software ships with the device), and set the framerate with this software. Of course, you have to pre-configure the device just once, then save that configuration in its flash memory.

To get a laser scan you must proceed like that :

CLMS200Eth laser(string("192.168.0.10"), 1234);
laser.turnOn();
bool isOutObs, hardwareError;
CObservation2DRangeScan outObs;
laser.doProcessSimple(isOutObs, outObs, hardwareError);

The sensor pose on the vehicle could be loaded from an ini configuration file with :

   PARAMETERS IN THE ".INI"-LIKE CONFIGURATION STRINGS:
  -------------------------------------------------------
    [supplied_section_name]
      ip_address = 192.168.0.50 ;a string wich is the SICK's ip adress
*(default is 192.168.0.1)
    TCP_port = 1234         ; an integer value : the tcp ip port on wich the
*sick is listening (default is 2111).
    pose_x=0.21 ; Laser range scaner 3D position in the robot (meters)
    pose_y=0
    pose_z=0.34
    pose_yaw=0  ; Angles in degrees
    pose_pitch=0
    pose_roll=0

This class doesn't configure the SICK LMS sensor, it is recomended to configure the sensor via the the SICK software : SOPAS.

Note: This class was contributed by Adrien Barral - Robopec (France)

Definition at line 72 of file CLMS100eth.h.

#include <mrpt/hwdrivers/CLMS100eth.h>

Inheritance diagram for mrpt::hwdrivers::CLMS100Eth:

Public Types
enum	TSensorState { ssInitializing = 0, ssWorking, ssError, ssUninitialized }
	The current state of the sensor. More...

using	Ptr = std::shared_ptr< CGenericSensor >

using	TListObservations = std::multimap< mrpt::system::TTimeStamp, mrpt::serialization::CSerializable::Ptr >

using	TListObsPair = std::pair< mrpt::system::TTimeStamp, mrpt::serialization::CSerializable::Ptr >

Public Member Functions
	CLMS100Eth (std::string _ip=std::string("192.168.0.1"), unsigned int _port=2111)
	Constructor. More...

	~CLMS100Eth () override
	Destructor. More...

void	doProcessSimple (bool &outThereIsObservation, mrpt::obs::CObservation2DRangeScan &outObservation, bool &hardwareError) override
	This function acquire a laser scan from the device. More...

bool	turnOn () override
	This method must be called before trying to get a laser scan. More...

bool	turnOff () override
	This method could be called manually to stop communication with the device. More...

void	setSensorPose (const mrpt::poses::CPose3D &_pose)
	A method to set the sensor pose on the robot. More...

void	doProcess () override
	This method should be called periodically. More...

void	initialize () override
	Initialize the sensor according to the parameters previously read in the configuration file. More...

void	showPreview (bool enable=true)
	Enables GUI visualization in real-time. More...

void	bindIO (const std::shared_ptr< mrpt::io::CStream > &streamIO)
	Binds the object to a given I/O channel. More...

void	getObservation (bool &outThereIsObservation, mrpt::obs::CObservation2DRangeScan &outObservation, bool &hardwareError)
	Get the last observation from the sensor, if available, and unmarks it as being "the last one" (thus a new scan must arrive or subsequent calls will find no new observations). More...

double	getEstimatedScanPeriod () const
	Returns the empirical, filtered estimation for the period at which whole scans are being returned from calls to doProcessSimple() More...

virtual const mrpt::hwdrivers::TSensorClassId *	GetRuntimeClass () const =0

TSensorState	getState () const
	The current state of the sensor. More...

double	getProcessRate () const

std::string	getSensorLabel () const

void	setSensorLabel (const std::string &sensorLabel)

void	enableVerbose (bool enabled=true)
	Enable or disable extra debug info dumped to std::cout during sensor operation. More...

bool	isVerboseEnabled () const

void	loadConfig (const mrpt::config::CConfigFileBase &configSource, const std::string &section)
	Loads the generic settings common to any sensor (See CGenericSensor), then call to "loadConfig_sensorSpecific". More...

void	getObservations (TListObservations &lstObjects)
	Returns a list of enqueued objects, emptying it (thread-safe). More...

virtual void	setPathForExternalImages ([[maybe_unused]] const std::string &directory)
	Set the path where to save off-rawlog image files (will be ignored in those sensors where this is not applicable). More...

void	setExternalImageFormat (const std::string &ext)
	Set the extension ("jpg","gif","png",...) that determines the format of images saved externally The default is "jpg". More...

void	setExternalImageJPEGQuality (const unsigned int quality)
	The quality of JPEG compression, when external images is enabled and the format is "jpg". More...

unsigned int	getExternalImageJPEGQuality () const

Static Public Member Functions
static std::array< mrpt::system::TConsoleColor, NUMBER_OF_VERBOSITY_LEVELS > &	logging_levels_to_colors ()
	Map from VerbosityLevels to their corresponding mrpt::system::TConsoleColor. More...

static std::array< std::string, NUMBER_OF_VERBOSITY_LEVELS > &	logging_levels_to_names ()
	Map from VerbosityLevels to their corresponding names. More...

static void	registerClass (const TSensorClassId *pNewClass)
	Register a class into the internal list of "CGenericSensor" descendents. More...

static CGenericSensor *	createSensor (const std::string &className)
	Creates a sensor by a name of the class. More...

static Ptr	createSensorPtr (const std::string &className)
	Just like createSensor, but returning a smart pointer to the newly created sensor object. More...

Protected Member Functions
void	loadConfig_sensorSpecific (const mrpt::config::CConfigFileBase &configSource, const std::string &iniSection) override
	Load sensor pose on the robot, or keep the default sensor pose. More...

void	loadCommonParams (const mrpt::config::CConfigFileBase &configSource, const std::string &iniSection)
	Should be call by derived classes at "loadConfig" (loads exclusion areas AND exclusion angles). More...

void	filterByExclusionAreas (mrpt::obs::CObservation2DRangeScan &obs) const
	Mark as invalid those points which (x,y) coordinates fall within the exclusion polygons. More...

void	filterByExclusionAngles (mrpt::obs::CObservation2DRangeScan &obs) const
	Mark as invalid those ranges in a set of forbiden angle ranges. More...

void	processPreview (const mrpt::obs::CObservation2DRangeScan &obs)
	Must be called inside the capture method to allow optional GUI preview of scans. More...

void	internal_notifyGoodScanNow ()
	Must be called from doProcessSimple() implementations. More...

bool	internal_notifyNoScanReceived ()
	Must be called from doProcessSimple() implementations. More...

void	appendObservations (const std::vector< mrpt::serialization::CSerializable::Ptr > &obj)
	This method must be called by derived classes to enqueue a new observation in the list to be returned by getObservations. More...

void	appendObservation (const mrpt::serialization::CSerializable::Ptr &obj)
	Like appendObservations() but for just one observation. More...

Protected Attributes
std::shared_ptr< mrpt::io::CStream >	m_stream
	The I/O channel (will be nullptr if not bound). More...

VerbosityLevel	m_min_verbosity_level {LVL_INFO}
	Provided messages with VerbosityLevel smaller than this value shall be ignored. More...

size_t	m_grab_decimation_counter {0}
	Used when "m_grab_decimation" is enabled. More...

TSensorState	m_state {ssInitializing}

bool	m_verbose {false}

std::string	m_path_for_external_images
	The path where to save off-rawlog images: empty means save images embedded in the rawlog. More...

std::string	m_external_images_format
	The extension ("jpg","gif","png",...) that determines the format of images saved externally. More...

unsigned int	m_external_images_jpeg_quality {95}
	For JPEG images, the quality (default=95%). More...

Common settings to any sensor, loaded in "loadConfig"
double	m_process_rate {0}
	See CGenericSensor. More...

size_t	m_max_queue_len {200}
	See CGenericSensor. More...

size_t	m_grab_decimation {0}
	If set to N>=2, only 1 out of N observations will be saved to m_objList. More...

std::string	m_sensorLabel
	See CGenericSensor. More...

Private Member Functions
void	generateCmd (const char *cmd)
	Add the start and end character. More...

bool	checkIsConnected ()

bool	decodeLogIn (char *msg)

bool	decodeScanCfg (std::istringstream &stream)

bool	decodeScanDataCfg (std::istringstream &stream)

bool	decodeScan (char *buf, mrpt::obs::CObservation2DRangeScan &outObservation)

void	sendCommand (const char *cmd)

void	roughPrint (char *msg)

Private Attributes
std::string	m_ip

unsigned int	m_port = 0

mrpt::comms::CClientTCPSocket	m_client

bool	m_turnedOn {false}

std::string	m_cmd

bool	m_connected {false}

unsigned int	m_scanFrequency = 0

double	m_angleResolution = 0

double	m_startAngle = 0

double	m_stopAngle = 0

mrpt::poses::CPose3D	m_sensorPose

double	m_maxRange {20.0}

double	m_beamApperture = 0

Logging methods
void	logStr (const VerbosityLevel level, std::string_view msg_str) const
	Main method to add the specified message string to the logger. More...

void	logFmt (const VerbosityLevel level, const char *fmt,...) const MRPT_printf_format_check(3
	Alternative logging method, which mimics the printf behavior. More...

void void	logCond (const VerbosityLevel level, bool cond, const std::string &msg_str) const
	Log the given message only if the condition is satisfied. More...

void	setLoggerName (const std::string &name)
	Set the name of the COutputLogger instance. More...

std::string	getLoggerName () const
	Return the name of the COutputLogger instance. More...

void	setMinLoggingLevel (const VerbosityLevel level)
	Set the minimum logging level for which the incoming logs are going to be taken into account. More...

void	setVerbosityLevel (const VerbosityLevel level)
	alias of setMinLoggingLevel() More...

VerbosityLevel	getMinLoggingLevel () const

bool	isLoggingLevelVisible (VerbosityLevel level) const

void	getLogAsString (std::string &log_contents) const
	Fill the provided string with the contents of the logger's history in std::string representation. More...

std::string	getLogAsString () const
	Get the history of COutputLogger instance in a string representation. More...

void	writeLogToFile (const std::string *fname_in=nullptr) const
	Write the contents of the COutputLogger instance to an external file. More...

void	dumpLogToConsole () const
	Dump the current contents of the COutputLogger instance in the terminal window. More...

std::string	getLoggerLastMsg () const
	Return the last Tmsg instance registered in the logger history. More...

void	getLoggerLastMsg (std::string &msg_str) const
	Fill inputtted string with the contents of the last message in history. More...

void	loggerReset ()
	Reset the contents of the logger instance. More...

void	logRegisterCallback (output_logger_callback_t userFunc)

bool	logDeregisterCallback (output_logger_callback_t userFunc)

bool	logging_enable_console_output {true}
	[Default=true] Set it to false in case you don't want the logged messages to be dumped to the output automatically. More...

bool	logging_enable_keep_record {false}
	[Default=false] Enables storing all messages into an internal list. More...

Member Typedef Documentation

◆ Ptr

using mrpt::hwdrivers::CGenericSensor::Ptr = std::shared_ptr<CGenericSensor>

inherited

Definition at line 73 of file CGenericSensor.h.

◆ TListObservations

using mrpt::hwdrivers::CGenericSensor::TListObservations = std::multimap< mrpt::system::TTimeStamp, mrpt::serialization::CSerializable::Ptr>

inherited

Definition at line 77 of file CGenericSensor.h.

◆ TListObsPair

using mrpt::hwdrivers::CGenericSensor::TListObsPair = std::pair< mrpt::system::TTimeStamp, mrpt::serialization::CSerializable::Ptr>

inherited

Definition at line 79 of file CGenericSensor.h.

Member Enumeration Documentation

◆ TSensorState

enum mrpt::hwdrivers::CGenericSensor::TSensorState

inherited

The current state of the sensor.

See also: CGenericSensor::getState

Enumerator
ssInitializing
ssWorking
ssError
ssUninitialized

Definition at line 84 of file CGenericSensor.h.

Constructor & Destructor Documentation

◆ CLMS100Eth()

CLMS100Eth::CLMS100Eth	(	std::string	_ip = `std::string("192.168.0.1")`,
		unsigned int	_port = `2111`
	)

Constructor.

Note that there is default arguments, here you can customize IP Adress and TCP Port of your device.

Definition at line 30 of file CLMS100eth.cpp.

References mrpt::system::LVL_DEBUG.

◆ ~CLMS100Eth()

CLMS100Eth::~CLMS100Eth ( )

override

Destructor.

Close communcation with the device, and free memory.

Definition at line 41 of file CLMS100eth.cpp.

Member Function Documentation

◆ appendObservation()

void mrpt::hwdrivers::CGenericSensor::appendObservation ( const mrpt::serialization::CSerializable::Ptr & obj )

inlineprotectedinherited

Like appendObservations() but for just one observation.

Definition at line 180 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::appendObservations().

Referenced by mrpt::hwdrivers::CIMUXSens_MT4::doProcess(), mrpt::hwdrivers::CIMUXSens::doProcess(), mrpt::hwdrivers::CGyroKVHDSP3000::doProcess(), mrpt::hwdrivers::CSkeletonTracker::doProcess(), mrpt::hwdrivers::CSwissRanger3DCamera::doProcess(), mrpt::hwdrivers::C2DRangeFinderAbstract::doProcess(), mrpt::hwdrivers::CCANBusReader::doProcess(), mrpt::hwdrivers::CVelodyneScanner::doProcess(), and mrpt::hwdrivers::CGPSInterface::flushParsedMessagesNow().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ appendObservations()

void CGenericSensor::appendObservations ( const std::vector< mrpt::serialization::CSerializable::Ptr > & obj )

protectedinherited

This method must be called by derived classes to enqueue a new observation in the list to be returned by getObservations.

Passed objects must be created in dynamic memory and a smart pointer passed. Example of creation:

  mrpt::obs::CObservationGPS::Ptr  o = CObservationGPS::Ptr( new
CObservationGPS() );
  o-> .... // Set data
  appendObservation(o);

If several observations are passed at once in the vector, they'll be considered as a block regarding the grabbing decimation factor.

Definition at line 48 of file CGenericSensor.cpp.

References CLASS_ID, mrpt::hwdrivers::CGenericSensor::m_csObjList, mrpt::hwdrivers::CGenericSensor::m_grab_decimation, mrpt::hwdrivers::CGenericSensor::m_grab_decimation_counter, mrpt::hwdrivers::CGenericSensor::m_objList, and THROW_EXCEPTION.

Referenced by mrpt::hwdrivers::CGenericSensor::appendObservation(), mrpt::hwdrivers::CNationalInstrumentsDAQ::doProcess(), and mrpt::hwdrivers::CKinect::doProcess().

Here is the caller graph for this function:

◆ bindIO()

void C2DRangeFinderAbstract::bindIO ( const std::shared_ptr< mrpt::io::CStream > & streamIO )

inherited

Binds the object to a given I/O channel.

The stream object must not be deleted before the destruction of this class.

See also: comms::CSerialPort

Definition at line 35 of file C2DRangeFinderAbstract.cpp.

References mrpt::hwdrivers::C2DRangeFinderAbstract::m_csChangeStream, and mrpt::hwdrivers::C2DRangeFinderAbstract::m_stream.

Referenced by mrpt::hwdrivers::CHokuyoURG::ensureStreamIsOpen().

Here is the caller graph for this function:

◆ checkIsConnected()

bool CLMS100Eth::checkIsConnected ( )

private

Definition at line 82 of file CLMS100eth.cpp.

References MRPT_LOG_ERROR_FMT.

◆ createSensor()

CGenericSensor * CGenericSensor::createSensor ( const std::string & className )

staticinherited

Creates a sensor by a name of the class.

Typically the user may want to create a smart pointer around the returned pointer, whis is made with:

CGenericSensor::Ptr sensor = CGenericSensor::Ptr(

CGenericSensor::createSensor("XXX") );

Returns: A pointer to a new class, or nullptr if class name is unknown.

Definition at line 97 of file CGenericSensor.cpp.

References mrpt::hwdrivers::CGenericSensor::get_registered_sensor_classes().

Referenced by mrpt::hwdrivers::CGenericSensor::createSensorPtr().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ createSensorPtr()

static Ptr mrpt::hwdrivers::CGenericSensor::createSensorPtr ( const std::string & className )

inlinestaticinherited

Just like createSensor, but returning a smart pointer to the newly created sensor object.

Definition at line 210 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::createSensor().

Referenced by mrpt::apps::RawlogGrabberApp::SensorThread().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ decodeLogIn()

bool mrpt::hwdrivers::CLMS100Eth::decodeLogIn ( char * msg )

private

◆ decodeScan()

bool CLMS100Eth::decodeScan	(	char *	buf,
		mrpt::obs::CObservation2DRangeScan &	outObservation
	)

private

Definition at line 227 of file CLMS100eth.cpp.

Here is the call graph for this function:

◆ decodeScanCfg()

bool mrpt::hwdrivers::CLMS100Eth::decodeScanCfg ( std::istringstream & stream )

private

◆ decodeScanDataCfg()

bool mrpt::hwdrivers::CLMS100Eth::decodeScanDataCfg ( std::istringstream & stream )

private

◆ doProcess()

void CLMS100Eth::doProcess ( )

overridevirtual

This method should be called periodically.

Period depend on the process_rate in the configuration file.

Reimplemented from mrpt::hwdrivers::C2DRangeFinderAbstract.

Definition at line 350 of file CLMS100eth.cpp.

References THROW_EXCEPTION.

◆ doProcessSimple()

void CLMS100Eth::doProcessSimple	(	bool &	outThereIsObservation,
		mrpt::obs::CObservation2DRangeScan &	outObservation,
		bool &	hardwareError
	)

overridevirtual

This function acquire a laser scan from the device.

If an error occured, hardwareError will be set to true. The new laser scan will be stored in the outObservation argument.

Exceptions

This	method throw exception if the frame received from the LMS 100 contain the following bad parameters : Status is not OK Data in the scan aren't DIST1 (may be RSSIx or DIST2).

Implements mrpt::hwdrivers::C2DRangeFinderAbstract.

Definition at line 308 of file CLMS100eth.cpp.

References MRPT_LOG_ERROR.

◆ dumpLogToConsole()

void COutputLogger::dumpLogToConsole ( ) const

inherited

Dump the current contents of the COutputLogger instance in the terminal window.

See also: writeToFile

Definition at line 190 of file COutputLogger.cpp.

◆ enableVerbose()

void mrpt::hwdrivers::CGenericSensor::enableVerbose ( bool enabled = true )

inlineinherited

Enable or disable extra debug info dumped to std::cout during sensor operation.

Default: disabled unless the environment variable "MRPT_HWDRIVERS_VERBOSE" is set to "1" during object creation.

Definition at line 106 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::m_verbose.

◆ filterByExclusionAngles()

void C2DRangeFinderAbstract::filterByExclusionAngles ( mrpt::obs::CObservation2DRangeScan & obs ) const

protectedinherited

Mark as invalid those ranges in a set of forbiden angle ranges.

See also: loadExclusionAreas

Definition at line 205 of file C2DRangeFinderAbstract.cpp.

References mrpt::obs::CObservation2DRangeScan::filterByExclusionAngles(), and mrpt::hwdrivers::C2DRangeFinderAbstract::m_lstExclusionAngles.

Referenced by mrpt::hwdrivers::CRoboPeakLidar::doProcessSimple(), mrpt::hwdrivers::CSickLaserUSB::doProcessSimple(), mrpt::hwdrivers::CSickLaserSerial::doProcessSimple(), and mrpt::hwdrivers::CHokuyoURG::doProcessSimple().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ filterByExclusionAreas()

void C2DRangeFinderAbstract::filterByExclusionAreas ( mrpt::obs::CObservation2DRangeScan & obs ) const

protectedinherited

Mark as invalid those points which (x,y) coordinates fall within the exclusion polygons.

See also: loadExclusionAreas

Definition at line 196 of file C2DRangeFinderAbstract.cpp.

References mrpt::obs::CObservation2DRangeScan::filterByExclusionAreas(), and mrpt::hwdrivers::C2DRangeFinderAbstract::m_lstExclusionPolys.

Referenced by mrpt::hwdrivers::CRoboPeakLidar::doProcessSimple(), mrpt::hwdrivers::CSickLaserUSB::doProcessSimple(), mrpt::hwdrivers::CSickLaserSerial::doProcessSimple(), and mrpt::hwdrivers::CHokuyoURG::doProcessSimple().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ generateCmd()

void CLMS100Eth::generateCmd ( const char * cmd )

private

Add the start and end character.

Definition at line 217 of file CLMS100eth.cpp.

References mrpt::format(), and MRPT_LOG_ERROR.

Here is the call graph for this function:

◆ getEstimatedScanPeriod()

double mrpt::hwdrivers::C2DRangeFinderAbstract::getEstimatedScanPeriod ( ) const

inlineinherited

Returns the empirical, filtered estimation for the period at which whole scans are being returned from calls to doProcessSimple()

Note: : Units: seconds

Definition at line 163 of file C2DRangeFinderAbstract.h.

References mrpt::hwdrivers::C2DRangeFinderAbstract::m_estimated_scan_period.

◆ getExternalImageJPEGQuality()

unsigned int mrpt::hwdrivers::CGenericSensor::getExternalImageJPEGQuality ( ) const

inlineinherited

Definition at line 279 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::m_external_images_jpeg_quality.

◆ getLogAsString() [1/2]

void COutputLogger::getLogAsString ( std::string & log_contents ) const

inherited

Fill the provided string with the contents of the logger's history in std::string representation.

Definition at line 154 of file COutputLogger.cpp.

◆ getLogAsString() [2/2]

std::string COutputLogger::getLogAsString ( ) const

inherited

Get the history of COutputLogger instance in a string representation.

Definition at line 159 of file COutputLogger.cpp.

Referenced by mrpt::graphslam::deciders::CICPCriteriaNRD< GRAPH_T >::getDescriptiveReport().

Here is the caller graph for this function:

◆ getLoggerLastMsg() [1/2]

std::string COutputLogger::getLoggerLastMsg ( ) const

inherited

Return the last Tmsg instance registered in the logger history.

Definition at line 195 of file COutputLogger.cpp.

References mrpt::system::COutputLogger::TMsg::getAsString().

Here is the call graph for this function:

◆ getLoggerLastMsg() [2/2]

void COutputLogger::getLoggerLastMsg ( std::string & msg_str ) const

inherited

Fill inputtted string with the contents of the last message in history.

Definition at line 201 of file COutputLogger.cpp.

◆ getLoggerName()

std::string COutputLogger::getLoggerName ( ) const

inherited

Return the name of the COutputLogger instance.

See also: setLoggerName

Definition at line 143 of file COutputLogger.cpp.

◆ getMinLoggingLevel()

VerbosityLevel mrpt::system::COutputLogger::getMinLoggingLevel ( ) const

inlineinherited

See also: setMinLoggingLevel

Definition at line 201 of file system/COutputLogger.h.

References mrpt::system::COutputLogger::m_min_verbosity_level.

Referenced by mrpt::apps::RawlogGrabberApp::dump_verbose_info(), mrpt::maps::CRandomFieldGridMap2D::isEnabledVerbose(), mrpt::slam::CMetricMapBuilderRBPF::processActionObservation(), mrpt::apps::CGridMapAlignerApp::run(), mrpt::apps::RBPF_SLAM_App_Base::run(), and mrpt::apps::ICP_SLAM_App_Base::run().

Here is the caller graph for this function:

◆ getObservation()

void C2DRangeFinderAbstract::getObservation	(	bool &	outThereIsObservation,
		mrpt::obs::CObservation2DRangeScan &	outObservation,
		bool &	hardwareError
	)

inherited

Get the last observation from the sensor, if available, and unmarks it as being "the last one" (thus a new scan must arrive or subsequent calls will find no new observations).

Definition at line 45 of file C2DRangeFinderAbstract.cpp.

References mrpt::hwdrivers::C2DRangeFinderAbstract::m_csLastObservation, mrpt::hwdrivers::C2DRangeFinderAbstract::m_hardwareError, mrpt::hwdrivers::C2DRangeFinderAbstract::m_lastObservation, and mrpt::hwdrivers::C2DRangeFinderAbstract::m_lastObservationIsNew.

◆ getObservations()

void CGenericSensor::getObservations ( TListObservations & lstObjects )

inherited

Returns a list of enqueued objects, emptying it (thread-safe).

The objects must be freed by the invoker.

Definition at line 85 of file CGenericSensor.cpp.

References mrpt::hwdrivers::CGenericSensor::m_csObjList, and mrpt::hwdrivers::CGenericSensor::m_objList.

Referenced by TEST().

Here is the caller graph for this function:

◆ getProcessRate()

double mrpt::hwdrivers::CGenericSensor::getProcessRate ( ) const

inlineinherited

Definition at line 94 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::m_process_rate.

◆ GetRuntimeClass()

virtual const mrpt::hwdrivers::TSensorClassId* mrpt::hwdrivers::CGenericSensor::GetRuntimeClass ( ) const

pure virtualinherited

◆ getSensorLabel()

std::string mrpt::hwdrivers::CGenericSensor::getSensorLabel ( ) const

inlineinherited

Definition at line 95 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::m_sensorLabel.

◆ getState()

TSensorState mrpt::hwdrivers::CGenericSensor::getState ( ) const

inlineinherited

The current state of the sensor.

Definition at line 93 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::m_state.

◆ initialize()

void CLMS100Eth::initialize ( )

overridevirtual

Initialize the sensor according to the parameters previously read in the configuration file.

Reimplemented from mrpt::hwdrivers::CGenericSensor.

Definition at line 46 of file CLMS100eth.cpp.

References THROW_EXCEPTION.

◆ internal_notifyGoodScanNow()

void C2DRangeFinderAbstract::internal_notifyGoodScanNow ( )

protectedinherited

Must be called from doProcessSimple() implementations.

Definition at line 87 of file C2DRangeFinderAbstract.cpp.

References INVALID_TIMESTAMP, mrpt::hwdrivers::C2DRangeFinderAbstract::m_estimated_scan_period, mrpt::hwdrivers::C2DRangeFinderAbstract::m_failure_waiting_scan_counter, mrpt::hwdrivers::C2DRangeFinderAbstract::m_last_good_scan, mrpt::system::now(), and mrpt::system::timeDifference().

Referenced by mrpt::hwdrivers::CSickLaserSerial::doProcessSimple(), and mrpt::hwdrivers::CHokuyoURG::doProcessSimple().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ internal_notifyNoScanReceived()

bool C2DRangeFinderAbstract::internal_notifyNoScanReceived ( )

protectedinherited

Must be called from doProcessSimple() implementations.

Returns true if ok, false if this seems strange and should return an error condition to the user.

Definition at line 102 of file C2DRangeFinderAbstract.cpp.

References INVALID_TIMESTAMP, mrpt::hwdrivers::C2DRangeFinderAbstract::m_estimated_scan_period, mrpt::hwdrivers::C2DRangeFinderAbstract::m_failure_waiting_scan_counter, mrpt::hwdrivers::C2DRangeFinderAbstract::m_last_good_scan, mrpt::hwdrivers::C2DRangeFinderAbstract::m_max_missed_scan_failures, mrpt::system::now(), and mrpt::system::timeDifference().

Referenced by mrpt::hwdrivers::CSickLaserSerial::doProcessSimple(), and mrpt::hwdrivers::CHokuyoURG::doProcessSimple().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ isLoggingLevelVisible()

bool mrpt::system::COutputLogger::isLoggingLevelVisible ( VerbosityLevel level ) const

inlineinherited

Definition at line 202 of file system/COutputLogger.h.

References mrpt::system::COutputLogger::m_min_verbosity_level.

Referenced by mrpt::slam::CMetricMapBuilderRBPF::processActionObservation(), and mrpt::system::COutputLoggerStreamWrapper::~COutputLoggerStreamWrapper().

Here is the caller graph for this function:

◆ isVerboseEnabled()

bool mrpt::hwdrivers::CGenericSensor::isVerboseEnabled ( ) const

inlineinherited

Definition at line 107 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::m_verbose.

◆ loadCommonParams()

void C2DRangeFinderAbstract::loadCommonParams	(	const mrpt::config::CConfigFileBase &	configSource,
		const std::string &	iniSection
	)

protectedinherited

Should be call by derived classes at "loadConfig" (loads exclusion areas AND exclusion angles).

This loads a sequence of vertices of a polygon given by its (x,y) coordinates relative to the vehicle, that is, taking into account the "sensorPose".

exclusionZoneu_x
exclusionZoneu_y for u=1,2,3,... All points within the 2D polygon will be ignored, for any Z, unless an optional entry is found:
exclusionZoneu_z=[z_min z_max] In that case, only the points within the 2D polygon AND the given range in Z will be ignored.

The number of zones is variable, but they must start at 1 and be consecutive.

This also loads any other common params (e.g. 'preview')

See also: filterByExclusionAreas

Definition at line 119 of file C2DRangeFinderAbstract.cpp.

References ASSERT_, ASSERTMSG_, mrpt::DEG2RAD(), mrpt::containers::end(), mrpt::format(), mrpt::hwdrivers::C2DRangeFinderAbstract::m_lstExclusionAngles, mrpt::hwdrivers::C2DRangeFinderAbstract::m_lstExclusionPolys, mrpt::hwdrivers::C2DRangeFinderAbstract::m_max_missed_scan_failures, M_PI, mrpt::hwdrivers::C2DRangeFinderAbstract::m_showPreview, mrpt::config::CConfigFileBase::read_bool(), mrpt::config::CConfigFileBase::read_double(), mrpt::config::CConfigFileBase::read_int(), and mrpt::config::CConfigFileBase::read_vector().

Referenced by mrpt::hwdrivers::CSickLaserUSB::loadConfig_sensorSpecific(), mrpt::hwdrivers::CRoboPeakLidar::loadConfig_sensorSpecific(), mrpt::hwdrivers::CSickLaserSerial::loadConfig_sensorSpecific(), and mrpt::hwdrivers::CHokuyoURG::loadConfig_sensorSpecific().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ loadConfig()

void CGenericSensor::loadConfig	(	const mrpt::config::CConfigFileBase &	cfg,
		const std::string &	sect
	)

inherited

Loads the generic settings common to any sensor (See CGenericSensor), then call to "loadConfig_sensorSpecific".

Exceptions

This	method throws an exception with a descriptive message if some critical parameter is missing or has an invalid value.

Definition at line 126 of file CGenericSensor.cpp.

References mrpt::hwdrivers::CGenericSensor::loadConfig_sensorSpecific(), mrpt::hwdrivers::CGenericSensor::m_grab_decimation, mrpt::hwdrivers::CGenericSensor::m_grab_decimation_counter, mrpt::hwdrivers::CGenericSensor::m_max_queue_len, mrpt::hwdrivers::CGenericSensor::m_process_rate, mrpt::hwdrivers::CGenericSensor::m_sensorLabel, MRPT_END, MRPT_START, mrpt::config::CConfigFileBase::read_double(), mrpt::config::CConfigFileBase::read_int(), mrpt::config::CConfigFileBase::read_string(), and sect.

Here is the call graph for this function:

◆ loadConfig_sensorSpecific()

void CLMS100Eth::loadConfig_sensorSpecific	(	const mrpt::config::CConfigFileBase &	configSource,
		const std::string &	iniSection
	)

overrideprotectedvirtual

Load sensor pose on the robot, or keep the default sensor pose.

Implements mrpt::hwdrivers::CGenericSensor.

Definition at line 57 of file CLMS100eth.cpp.

References mrpt::DEG2RAD(), mrpt::config::CConfigFileBase::read_float(), mrpt::config::CConfigFileBase::read_int(), and mrpt::config::CConfigFileBase::read_string().

Here is the call graph for this function:

◆ logCond()

void COutputLogger::logCond	(	const VerbosityLevel	level,
		bool	cond,
		const std::string &	msg_str
	)		const

inherited

Log the given message only if the condition is satisfied.

See also: log, logFmt

Definition at line 131 of file COutputLogger.cpp.

◆ logDeregisterCallback()

bool COutputLogger::logDeregisterCallback ( output_logger_callback_t userFunc )

inherited

Returns: true if an entry was found and deleted.

Definition at line 291 of file COutputLogger.cpp.

References getAddress(), and mrpt::system::COutputLogger::m_listCallbacks.

Here is the call graph for this function:

◆ logFmt()

void COutputLogger::logFmt	(	const VerbosityLevel	level,
		const char *	fmt,
			...
	)		const

inherited

Alternative logging method, which mimics the printf behavior.

Handy for not having to first use mrpt::format to pass a std::string message to logStr

// instead of:
logStr(mrpt::format("Today is the %d of %s, %d", 15, "July", 2016));
// one can use:
logFmt("Today is the %d of %s, %d", 15, "July", 2016);

See also: logStr, logCond

Definition at line 91 of file COutputLogger.cpp.

Referenced by mrpt::hmtslam::CHMTSLAM::areaAbstraction(), mrpt::graphslam::deciders::CICPCriteriaNRD< GRAPH_T >::CICPCriteriaNRD(), mrpt::hmtslam::CTopLCDetector_GridMatching::computeTopologicalObservationModel(), CGraphSlamHandler< GRAPH_T >::execute(), mrpt::math::CLevenbergMarquardtTempl< VECTORTYPE, USERPARAM >::execute(), CGraphSlamHandler< GRAPH_T >::initOutputDir(), CGraphSlamHandler< GRAPH_T >::initVisualization(), mrpt::nav::CNavigatorManualSequence::navigationStep(), mrpt::nav::CAbstractNavigator::performNavigationStepNavigating(), CGraphSlamHandler< GRAPH_T >::readConfigFname(), CGraphSlamHandler< GRAPH_T >::saveResults(), CGraphSlamHandler< GRAPH_T >::setResultsDirName(), mrpt::nav::CReactiveNavigationSystem::STEP1_InitPTGs(), mrpt::hmtslam::CHMTSLAM::thread_3D_viewer(), mrpt::hmtslam::CHMTSLAM::thread_LSLAM(), mrpt::hmtslam::CHMTSLAM::thread_TBI(), and CGraphSlamHandler< GRAPH_T >::~CGraphSlamHandler().

Here is the caller graph for this function:

◆ loggerReset()

void COutputLogger::loggerReset ( )

inherited

Reset the contents of the logger instance.

Called upon construction.

Definition at line 206 of file COutputLogger.cpp.

References mrpt::system::LVL_INFO.

◆ logging_levels_to_colors()

std::array< mrpt::system::TConsoleColor, NUMBER_OF_VERBOSITY_LEVELS > & COutputLogger::logging_levels_to_colors ( )

staticinherited

Map from VerbosityLevels to their corresponding mrpt::system::TConsoleColor.

Handy for coloring the input based on the verbosity of the message

Definition at line 47 of file COutputLogger.cpp.

References logging_levels_to_colors.

Referenced by mrpt::system::COutputLogger::TMsg::dumpToConsole().

Here is the caller graph for this function:

◆ logging_levels_to_names()

std::array< std::string, NUMBER_OF_VERBOSITY_LEVELS > & COutputLogger::logging_levels_to_names ( )

staticinherited

Map from VerbosityLevels to their corresponding names.

Handy for printing the current message VerbosityLevel along with the actual content

Definition at line 60 of file COutputLogger.cpp.

References logging_levels_to_names.

Referenced by mrpt::system::COutputLogger::TMsg::getAsString().

Here is the caller graph for this function:

◆ logRegisterCallback()

void COutputLogger::logRegisterCallback ( output_logger_callback_t userFunc )

inherited

Definition at line 278 of file COutputLogger.cpp.

References mrpt::system::COutputLogger::m_listCallbacks.

◆ logStr()

void COutputLogger::logStr	(	const VerbosityLevel	level,
		std::string_view	msg_str
	)		const

inherited

Main method to add the specified message string to the logger.

See also: logCond, logFmt

Definition at line 72 of file COutputLogger.cpp.

References mrpt::system::COutputLogger::TMsg::body, mrpt::system::COutputLogger::TMsg::dumpToConsole(), mrpt::system::COutputLogger::TMsg::level, mrpt::system::COutputLogger::TMsg::name, and mrpt::system::COutputLogger::TMsg::timestamp.

Referenced by mrpt::slam::PF_implementation< mrpt::math::TPose3D, CMonteCarloLocalization3D, mrpt::bayes::particle_storage_mode::VALUE >::PF_SLAM_implementation_pfAuxiliaryPFStandardAndOptimal(), mrpt::nav::CReactiveNavigationSystem::STEP1_InitPTGs(), mrpt::system::COutputLoggerStreamWrapper::~COutputLoggerStreamWrapper(), and mrpt::system::CTimeLoggerSaveAtDtor::~CTimeLoggerSaveAtDtor().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ processPreview()

void C2DRangeFinderAbstract::processPreview ( const mrpt::obs::CObservation2DRangeScan & obs )

protectedinherited

Must be called inside the capture method to allow optional GUI preview of scans.

Definition at line 211 of file C2DRangeFinderAbstract.cpp.

References mrpt::gui::CDisplayWindow3D::Create(), mrpt::hwdrivers::CGenericSensor::m_sensorLabel, mrpt::hwdrivers::C2DRangeFinderAbstract::m_showPreview, and mrpt::hwdrivers::C2DRangeFinderAbstract::m_win.

Referenced by mrpt::hwdrivers::CRoboPeakLidar::doProcessSimple(), mrpt::hwdrivers::CSickLaserUSB::doProcessSimple(), mrpt::hwdrivers::CSickLaserSerial::doProcessSimple(), and mrpt::hwdrivers::CHokuyoURG::doProcessSimple().

Here is the call graph for this function:

Here is the caller graph for this function:

◆ registerClass()

void CGenericSensor::registerClass ( const TSensorClassId * pNewClass )

staticinherited

Register a class into the internal list of "CGenericSensor" descendents.

Used internally in the macros DEFINE_GENERIC_SENSOR, etc...

Can be used as "CGenericSensor::registerClass( SENSOR_CLASS_ID(CMySensor) );" if building custom sensors outside mrpt libraries in user code.

Definition at line 115 of file CGenericSensor.cpp.

References mrpt::hwdrivers::TSensorClassId::className, and mrpt::hwdrivers::CGenericSensor::get_registered_sensor_classes().

Here is the call graph for this function:

◆ roughPrint()

void mrpt::hwdrivers::CLMS100Eth::roughPrint ( char * msg )

private

◆ sendCommand()

void CLMS100Eth::sendCommand ( const char * cmd )

private

Definition at line 208 of file CLMS100eth.cpp.

◆ setExternalImageFormat()

void mrpt::hwdrivers::CGenericSensor::setExternalImageFormat ( const std::string & ext )

inlineinherited

Set the extension ("jpg","gif","png",...) that determines the format of images saved externally The default is "jpg".

See also: setPathForExternalImages, setExternalImageJPEGQuality

Definition at line 268 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::m_external_images_format.

◆ setExternalImageJPEGQuality()

void mrpt::hwdrivers::CGenericSensor::setExternalImageJPEGQuality ( const unsigned int quality )

inlineinherited

The quality of JPEG compression, when external images is enabled and the format is "jpg".

See also: setExternalImageFormat

Definition at line 275 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::m_external_images_jpeg_quality.

◆ setLoggerName()

void COutputLogger::setLoggerName ( const std::string & name )

inherited

Set the name of the COutputLogger instance.

See also: getLoggerName

Definition at line 138 of file COutputLogger.cpp.

Referenced by mrpt::slam::CMetricMapBuilderICP::CMetricMapBuilderICP(), mrpt::slam::CMetricMapBuilderRBPF::CMetricMapBuilderRBPF(), mrpt::slam::CMonteCarloLocalization2D::CMonteCarloLocalization2D(), mrpt::slam::CMonteCarloLocalization3D::CMonteCarloLocalization3D(), mrpt::apps::ICP_SLAM_App_Base::ICP_SLAM_App_Base(), mrpt::apps::ICP_SLAM_App_Live::ICP_SLAM_App_Live(), mrpt::apps::ICP_SLAM_App_Rawlog::ICP_SLAM_App_Rawlog(), mrpt::graphslam::CWindowManager::initCWindowManager(), mrpt::apps::MonteCarloLocalization_Base::MonteCarloLocalization_Base(), mrpt::apps::RBPF_SLAM_App_Base::RBPF_SLAM_App_Base(), and mrpt::apps::RBPF_SLAM_App_Rawlog::RBPF_SLAM_App_Rawlog().

Here is the caller graph for this function:

◆ setMinLoggingLevel()

void COutputLogger::setMinLoggingLevel ( const VerbosityLevel level )

inherited

Set the minimum logging level for which the incoming logs are going to be taken into account.

String messages with specified VerbosityLevel smaller than the min, will not be outputted to the screen and neither will a record of them be stored in by the COutputLogger instance

Definition at line 144 of file COutputLogger.cpp.

Referenced by mrpt::maps::CRandomFieldGridMap2D::enableVerbose(), mrpt::math::CLevenbergMarquardtTempl< VECTORTYPE, USERPARAM >::execute(), generic_kf_slam_test(), generic_pf_test(), generic_rbpf_slam_test(), mrpt::apps::RawlogGrabberApp::initialize(), mrpt::hwdrivers::CHokuyoURG::initialize(), mrpt::graphslam::deciders::CICPCriteriaNRD< GRAPH_T >::loadParams(), mrpt::apps::CGridMapAlignerApp::run(), mrpt::apps::RBPF_SLAM_App_Base::run(), and mrpt::apps::ICP_SLAM_App_Base::run().

Here is the caller graph for this function:

◆ setPathForExternalImages()

virtual void mrpt::hwdrivers::CGenericSensor::setPathForExternalImages ( [ [maybe_unused] ] const std::string & directory )

inlinevirtualinherited

Set the path where to save off-rawlog image files (will be ignored in those sensors where this is not applicable).

An empty string (the default value at construction) means to save images embedded in the rawlog, instead of on separate files.

Exceptions

std::exception If the directory doesn't exists and cannot be created.

Definition at line 257 of file CGenericSensor.h.

◆ setSensorLabel()

void mrpt::hwdrivers::CGenericSensor::setSensorLabel ( const std::string & sensorLabel )

inlineinherited

Definition at line 96 of file CGenericSensor.h.

References mrpt::hwdrivers::CGenericSensor::m_sensorLabel.

◆ setSensorPose()

void CLMS100Eth::setSensorPose ( const mrpt::poses::CPose3D & _pose )

A method to set the sensor pose on the robot.

Equivalent to setting the sensor pose via loading it from a config file.

Definition at line 377 of file CLMS100eth.cpp.

◆ setVerbosityLevel()

void COutputLogger::setVerbosityLevel ( const VerbosityLevel level )

inherited

alias of setMinLoggingLevel()

Definition at line 149 of file COutputLogger.cpp.

Referenced by mrpt::nav::CAbstractNavigator::CAbstractNavigator(), mrpt::slam::CMetricMapBuilderRBPF::CMetricMapBuilderRBPF(), mrpt::comms::CServerTCPSocket::CServerTCPSocket(), mrpt::slam::CMetricMapBuilderRBPF::processActionObservation(), mrpt::math::ransac_detect_2D_lines(), and mrpt::apps::ICP_SLAM_App_Base::run().

Here is the caller graph for this function:

◆ showPreview()

void mrpt::hwdrivers::C2DRangeFinderAbstract::showPreview ( bool enable = true )

inlineinherited

Enables GUI visualization in real-time.

Definition at line 117 of file C2DRangeFinderAbstract.h.

References mrpt::hwdrivers::C2DRangeFinderAbstract::m_showPreview.

◆ turnOff()

bool CLMS100Eth::turnOff ( )

overridevirtual

This method could be called manually to stop communication with the device.

Method is also called by destructor.

Implements mrpt::hwdrivers::C2DRangeFinderAbstract.

Definition at line 104 of file CLMS100eth.cpp.

◆ turnOn()

bool CLMS100Eth::turnOn ( )

overridevirtual

This method must be called before trying to get a laser scan.

From the LMS100 datasheet : :

Login sMN SetAccessMode 03 F4724744F4724744
Set Scanarea and Resolution
sMN mLMPsetscancfg
SWN LMDscandatacfg 01 00 0 1 0 00 00 0 0 0 0 1
SMN mEEwriteall Je ne le fais pas, car ca écrit en mémoire non volatile...
Request scan : sRN LMDscandata OR sEN LMDscandata

Implements mrpt::hwdrivers::C2DRangeFinderAbstract.

Definition at line 112 of file CLMS100eth.cpp.

References MRPT_LOG_DEBUG_FMT, and MRPT_LOG_ERROR_FMT.

◆ writeLogToFile()

void COutputLogger::writeLogToFile ( const std::string * fname_in = nullptr ) const

inherited

Write the contents of the COutputLogger instance to an external file.

Upon call to this method, COutputLogger dumps the contents of all the logged commands so far to the specified external file. By default the filename is set to ${LOGGERNAME}.log except if the fname parameter is provided

See also: dumpToConsole, getAsString

Definition at line 165 of file COutputLogger.cpp.

References ASSERTMSG_, and mrpt::format().

Here is the call graph for this function:

Member Data Documentation

◆ logging_enable_console_output

bool mrpt::system::COutputLogger::logging_enable_console_output {true}

inherited

[Default=true] Set it to false in case you don't want the logged messages to be dumped to the output automatically.

Definition at line 240 of file system/COutputLogger.h.

◆ logging_enable_keep_record

bool mrpt::system::COutputLogger::logging_enable_keep_record {false}

inherited

[Default=false] Enables storing all messages into an internal list.

See also: writeLogToFile, getLogAsString

Definition at line 243 of file system/COutputLogger.h.

◆ m_angleResolution

double mrpt::hwdrivers::CLMS100Eth::m_angleResolution = 0

private

Definition at line 133 of file CLMS100eth.h.

◆ m_beamApperture

double mrpt::hwdrivers::CLMS100Eth::m_beamApperture = 0

private

Definition at line 138 of file CLMS100eth.h.

◆ m_client

mrpt::comms::CClientTCPSocket mrpt::hwdrivers::CLMS100Eth::m_client

private

Definition at line 128 of file CLMS100eth.h.

◆ m_cmd

std::string mrpt::hwdrivers::CLMS100Eth::m_cmd

private

Definition at line 130 of file CLMS100eth.h.

◆ m_connected

bool mrpt::hwdrivers::CLMS100Eth::m_connected {false}

private

Definition at line 131 of file CLMS100eth.h.

◆ m_external_images_format

std::string mrpt::hwdrivers::CGenericSensor::m_external_images_format

protectedinherited

The extension ("jpg","gif","png",...) that determines the format of images saved externally.

See also: setPathForExternalImages

Definition at line 158 of file CGenericSensor.h.

Referenced by mrpt::hwdrivers::CSwissRanger3DCamera::getNextObservation(), mrpt::hwdrivers::CSwissRanger3DCamera::loadConfig_sensorSpecific(), and mrpt::hwdrivers::CGenericSensor::setExternalImageFormat().

◆ m_external_images_jpeg_quality

unsigned int mrpt::hwdrivers::CGenericSensor::m_external_images_jpeg_quality {95}

protectedinherited

For JPEG images, the quality (default=95%).

Definition at line 160 of file CGenericSensor.h.

Referenced by mrpt::hwdrivers::CGenericSensor::getExternalImageJPEGQuality(), mrpt::hwdrivers::CSwissRanger3DCamera::getNextObservation(), mrpt::hwdrivers::CSwissRanger3DCamera::loadConfig_sensorSpecific(), and mrpt::hwdrivers::CGenericSensor::setExternalImageJPEGQuality().

◆ m_grab_decimation

size_t mrpt::hwdrivers::CGenericSensor::m_grab_decimation {0}

protectedinherited

If set to N>=2, only 1 out of N observations will be saved to m_objList.

Definition at line 139 of file CGenericSensor.h.

Referenced by mrpt::hwdrivers::CGenericSensor::appendObservations(), and mrpt::hwdrivers::CGenericSensor::loadConfig().

◆ m_grab_decimation_counter

size_t mrpt::hwdrivers::CGenericSensor::m_grab_decimation_counter {0}

protectedinherited

Used when "m_grab_decimation" is enabled.

Definition at line 146 of file CGenericSensor.h.

Referenced by mrpt::hwdrivers::CGenericSensor::appendObservations(), and mrpt::hwdrivers::CGenericSensor::loadConfig().

◆ m_ip

std::string mrpt::hwdrivers::CLMS100Eth::m_ip

private

Definition at line 126 of file CLMS100eth.h.

◆ m_max_queue_len

size_t mrpt::hwdrivers::CGenericSensor::m_max_queue_len {200}

protectedinherited

See CGenericSensor.

Definition at line 136 of file CGenericSensor.h.

Referenced by mrpt::hwdrivers::CGenericSensor::loadConfig().

◆ m_maxRange

double mrpt::hwdrivers::CLMS100Eth::m_maxRange {20.0}

private

Definition at line 137 of file CLMS100eth.h.

◆ m_min_verbosity_level

VerbosityLevel mrpt::system::COutputLogger::m_min_verbosity_level {LVL_INFO}

protectedinherited

Provided messages with VerbosityLevel smaller than this value shall be ignored.

Definition at line 253 of file system/COutputLogger.h.

Referenced by mrpt::system::COutputLogger::getMinLoggingLevel(), and mrpt::system::COutputLogger::isLoggingLevelVisible().

◆ m_path_for_external_images

std::string mrpt::hwdrivers::CGenericSensor::m_path_for_external_images

protectedinherited

The path where to save off-rawlog images: empty means save images embedded in the rawlog.

Definition at line 155 of file CGenericSensor.h.

Referenced by mrpt::hwdrivers::CSwissRanger3DCamera::getNextObservation(), and mrpt::hwdrivers::CSwissRanger3DCamera::setPathForExternalImages().

◆ m_port

unsigned int mrpt::hwdrivers::CLMS100Eth::m_port = 0

private

Definition at line 127 of file CLMS100eth.h.

◆ m_process_rate

double mrpt::hwdrivers::CGenericSensor::m_process_rate {0}

protectedinherited

See CGenericSensor.

Definition at line 134 of file CGenericSensor.h.

Referenced by mrpt::hwdrivers::CGenericSensor::getProcessRate(), mrpt::hwdrivers::CGyroKVHDSP3000::initialize(), and mrpt::hwdrivers::CGenericSensor::loadConfig().

◆ m_scanFrequency

unsigned int mrpt::hwdrivers::CLMS100Eth::m_scanFrequency = 0

private

Definition at line 132 of file CLMS100eth.h.

◆ m_sensorLabel

std::string mrpt::hwdrivers::CGenericSensor::m_sensorLabel

protectedinherited

See CGenericSensor.

Definition at line 141 of file CGenericSensor.h.

◆ m_sensorPose

mrpt::poses::CPose3D mrpt::hwdrivers::CLMS100Eth::m_sensorPose

private

Definition at line 136 of file CLMS100eth.h.

◆ m_startAngle

double mrpt::hwdrivers::CLMS100Eth::m_startAngle = 0

private

Definition at line 134 of file CLMS100eth.h.

◆ m_state

TSensorState mrpt::hwdrivers::CGenericSensor::m_state {ssInitializing}

protectedinherited

Definition at line 148 of file CGenericSensor.h.

◆ m_stopAngle

double mrpt::hwdrivers::CLMS100Eth::m_stopAngle = 0

private

Definition at line 135 of file CLMS100eth.h.

◆ m_stream

std::shared_ptr<mrpt::io::CStream> mrpt::hwdrivers::C2DRangeFinderAbstract::m_stream

protectedinherited

The I/O channel (will be nullptr if not bound).

Definition at line 69 of file C2DRangeFinderAbstract.h.

◆ m_turnedOn

bool mrpt::hwdrivers::CLMS100Eth::m_turnedOn {false}

private

Definition at line 129 of file CLMS100eth.h.

◆ m_verbose

bool mrpt::hwdrivers::CGenericSensor::m_verbose {false}

protectedinherited

Definition at line 149 of file CGenericSensor.h.

Detailed Description

Public Types

Public Member Functions

Static Public Member Functions

Protected Member Functions

Protected Attributes

Private Member Functions

Private Attributes

Logging methods

Member Typedef Documentation

◆ Ptr

◆ TListObservations

◆ TListObsPair

Member Enumeration Documentation

◆ TSensorState

Constructor & Destructor Documentation

◆ CLMS100Eth()

◆ ~CLMS100Eth()

Member Function Documentation

◆ appendObservation()

◆ appendObservations()

◆ bindIO()

◆ checkIsConnected()

◆ createSensor()

◆ createSensorPtr()

◆ decodeLogIn()

◆ decodeScan()

◆ decodeScanCfg()

◆ decodeScanDataCfg()

◆ doProcess()

◆ doProcessSimple()

◆ dumpLogToConsole()

◆ enableVerbose()

◆ filterByExclusionAngles()

◆ filterByExclusionAreas()

◆ generateCmd()

◆ getEstimatedScanPeriod()

◆ getExternalImageJPEGQuality()

◆ getLogAsString() [1/2]

◆ getLogAsString() [2/2]

◆ getLoggerLastMsg() [1/2]

◆ getLoggerLastMsg() [2/2]

◆ getLoggerName()

◆ getMinLoggingLevel()

◆ getObservation()

◆ getObservations()

◆ getProcessRate()

◆ GetRuntimeClass()

◆ getSensorLabel()

◆ getState()

◆ initialize()

◆ internal_notifyGoodScanNow()

◆ internal_notifyNoScanReceived()

◆ isLoggingLevelVisible()

◆ isVerboseEnabled()

◆ loadCommonParams()

◆ loadConfig()

◆ loadConfig_sensorSpecific()

◆ logCond()

◆ logDeregisterCallback()

◆ logFmt()

◆ loggerReset()

◆ logging_levels_to_colors()

◆ logging_levels_to_names()

◆ logRegisterCallback()

◆ logStr()

◆ processPreview()

◆ registerClass()

◆ roughPrint()

◆ sendCommand()

◆ setExternalImageFormat()

◆ setExternalImageJPEGQuality()

◆ setLoggerName()

◆ setMinLoggingLevel()

◆ setPathForExternalImages()

◆ setSensorLabel()

◆ setSensorPose()

◆ setVerbosityLevel()

◆ showPreview()

◆ turnOff()